Dec
18
to Dec 22

Komastu PC-11 Course

This Course is designed to provide participants who have Komatsu basic machine experience, knowledge, and skills a better understanding of the overall function, operation, maintenance, service, and repair of the PC240 to PC490-11. PRE-REQUISITES: Technical Participants • Introduction to Komatsu • All Foundation Courses • PC8 or PC10 Technical Course completed – OR – Advanced Hydraulics Course • Tier 4FINAL Level 1 (Webinar + Quiz) Course (on line)

View Event →
Jan
8
to Jan 11

John Deere K FT4 Loader

The purpose of the 4WD loader Capstone is to verify knowledge and skills of the John Deere Dealer technician. Verification will be determined by both a hands-on and written style test and validated with an 80% or higher score. Upon successful completion of this instructor led training event, the technician will be deemed certified on the current series of 4WD loaders. Certification yields reimbursement for a technician’s diagnostic time spent on an in-warranty machine but also develops individuals that are the best technicians to represent John Deere, their Dealership, and support the Customer and their business needs with 4WD Loaders.

View Event →
Jan
8
to Jan 12

Komatsu T4 Engines (IT4 & T4F)

This instructor-led course is designed to provide participants who have Komatsu engine experience, the necessary technical training for understanding the function, maintenance, service, repair & troubleshooting of the 6D107,6D114, 6D125,& 6D140 Tier 4 final & interim engines. This course is developed to carry the participant through both Tier 4 engine systems, starting with the Tier 4 interim engines. This course will cover changes to the Base Engines, Solutions by Horsepower Rating, the Variable Geometry Turbocharger, Diesel Particulate Filter, & all the related sensors for Tier 4 interim & final engines.  The DEF System including fluid properties, tank & cooling system, tank sensor, pump & injector modules, thawing & freeze prevention logic will be covered as well. Hands-on training will take place using a Tier 4 Final & Interim Machines. On-board diagnostic testing, creation of Inducement fault codes.

View Event →
Jan
8
to Jan 12

Basic Electrical

AIS Basic Electrical Course introduces students to complete basic foundation of electrical systems used in the heavy equipment industry. Technician will be taught Ohm’s law, and how to perform calculations. The class introduces relays, fuses, batteries, diodes, capacitors, and resistors; while being taught know how to properly test them. The technician will perform basic testing on starting and charging systems, as well as schematic reading on basic electrical systems. The student will also learn how to properly use a multi-meter to perform testing.

 

View Event →
Jan
15
to Jan 18

John Deere K FT4 Loader

The purpose of the 4WD loader Capstone is to verify knowledge and skills of the John Deere Dealer technician. Verification will be determined by both a hands-on and written style test and validated with an 80% or higher score. Upon successful completion of this instructor led training event, the technician will be deemed certified on the current series of 4WD loaders. Certification yields reimbursement for a technician’s diagnostic time spent on an in-warranty machine but also develops individuals that are the best technicians to represent John Deere, their Dealership, and support the Customer and their business needs with 4WD Loaders.

View Event →
Jan
22
to Jan 26

Basic Hydraulics

AIS Basic hydraulics is a complete hydraulic system overview used on today’s heavy equipment. The technician will be taught Pascal’s Law, safety, common component function and purpose, basics of oils, oil samples and cleanliness codes, as well as schematic reading on basic hydraulic systems. They will perform disassembly and assembly of gear, vane and piston pumps, reservoirs, hoses, control valves and cylinders. The technician will gain a basic knowledge of all these components. Load sensing systems as well as fluid conditioning will be covered. The technician will perform some basic hydraulic testing and adjusting.

 

 

View Event →
Jan
29
to Feb 2

Komatsu Tier 4 Engine Troubleshooting

This instructor-led course is designed to provide participants who have completed Komatsu Tier 4 Interim and Final engine classes, the necessary technical training to effectively troubleshoot and repair Komatsu Tier 4 Engine products (4D95, 4D107, 6D107, 6D114, 6D125, 6D140, and 6D170). This course is developed to aid the participant with the completion of Flash News 12061C. All troubleshooting procedures contained in the 12061C Flash News will be explained and performed including the use of the Insite tool, used as a diagnostic aid for the after-treatment system. Hands-on training will take place using representative Komatsu products utilizing the required tooling to complete Flash News 12061C. Hands on exercises will also include actual machine problems for the participant to troubleshoot and diagnose

View Event →
Jan
29
to Feb 2

Basic Hydraulics

AIS Basic hydraulics is a complete hydraulic system overview used on today’s heavy equipment. The technician will be taught Pascal’s Law, safety, common component function and purpose, basics of oils, oil samples and cleanliness codes, as well as schematic reading on basic hydraulic systems. They will perform disassembly and assembly of gear, vane and piston pumps, reservoirs, hoses, control valves and cylinders. The technician will gain a basic knowledge of all these components. Load sensing systems as well as fluid conditioning will be covered. The technician will perform some basic hydraulic testing and adjusting.

 

 

View Event →
Feb
6
to Feb 8

Compact Excavator Capstone (G-Series)

IMPORTANT! ***Students must bring their own computer to complete class.  If the student arrives without their computer they will not be able to complete the class and will be sent home.  Computers are not supplied for this class.***

Course Overview: The Compact Excavator Capstone (G-Series) is a two day instructor-led course. This course will cover topics such as hydraulics, electrical, monitor, engines and the use of Service ADVISOR™. This will also involve classroom and shop activities. Students attending this course should have strong Service ADVISOR™ skills and the ability to read electrical and hydraulic schematics.

Each student is required to bring a working laptop with Service ADVISOR™ and current data discs to class (please verify that G-Series machines are available on each laptop prior to class). The last day of the course will consist of a written and hands-on test.

View Event →
Feb
12
to Feb 16

Komatsu Tier 4 Engine Troubleshooting

This instructor-led course is designed to provide participants who have completed Komatsu Tier 4 Interim and Final engine classes, the necessary technical training to effectively troubleshoot and repair Komatsu Tier 4 Engine products (4D95, 4D107, 6D107, 6D114, 6D125, 6D140, and 6D170). This course is developed to aid the participant with the completion of Flash News 12061C. All troubleshooting procedures contained in the 12061C Flash News will be explained and performed including the use of the Insite tool, used as a diagnostic aid for the after-treatment system. Hands-on training will take place using representative Komatsu products utilizing the required tooling to complete Flash News 12061C. Hands on exercises will also include actual machine problems for the participant to troubleshoot and diagnose

View Event →
Feb
19
to Feb 23

Compact Excavator Capstone (G-Series)

IMPORTANT! ***Students must bring their own computer to complete class.  If the student arrives without their computer they will not be able to complete the class and will be sent home.  Computers are not supplied for this class.***

Course Overview: The Compact Excavator Capstone (G-Series) is a two day instructor-led course. This course will cover topics such as hydraulics, electrical, monitor, engines and the use of Service ADVISOR™. This will also involve classroom and shop activities. Students attending this course should have strong Service ADVISOR™ skills and the ability to read electrical and hydraulic schematics.

Each student is required to bring a working laptop with Service ADVISOR™ and current data discs to class (please verify that G-Series machines are available on each laptop prior to class). The last day of the course will consist of a written and hands-on test.

View Event →

Dec
12
to Dec 15

John Deere K Series Dozer

The 450K-850K FT4 crawler dozer capstone is a 3 day instructor-led course. The course covers theory of operation of electrical, hydrostatic, and hydraulic systems used on 450K-850K FT4 crawlers, as well as testing, adjustments, and diagnostics of the crawler family. The course is hands-on focused, with a majority of the class time spent around the machines. Students attending this course should have strong Service ADVISOR skills and the ability to read electrical, hydrostatic, and hydraulic schematics. Each student is required to bring a working laptop with Service ADVISOR and current data discs to class. Knowledge and skill tests will be administered during class. A score of 80% or higher is required to pass this capstone course. All ILT pricing assumes delivery at the Davenport Training Center. Additional costs will be charged if delivered at the dealership.

View Event →
Dec
11
to Dec 15

Komastu PC-11 Course

This Course is designed to provide participants who have Komatsu basic machine experience, knowledge, and skills a better understanding of the overall function, operation, maintenance, service, and repair of the PC240 to PC490-11. PRE-REQUISITES: Technical Participants • Introduction to Komatsu • All Foundation Courses • PC8 or PC10 Technical Course completed – OR – Advanced Hydraulics Course • Tier 4FINAL Level 1 (Webinar + Quiz) Course (on line)

View Event →
Dec
5
to Dec 8

John Deere K Series Dozer

The 450K-850K FT4 crawler dozer capstone is a 3 day instructor-led course. The course covers theory of operation of electrical, hydrostatic, and hydraulic systems used on 450K-850K FT4 crawlers, as well as testing, adjustments, and diagnostics of the crawler family. The course is hands-on focused, with a majority of the class time spent around the machines. Students attending this course should have strong Service ADVISOR skills and the ability to read electrical, hydrostatic, and hydraulic schematics. Each student is required to bring a working laptop with Service ADVISOR and current data discs to class. Knowledge and skill tests will be administered during class. A score of 80% or higher is required to pass this capstone course. All ILT pricing assumes delivery at the Davenport Training Center. Additional costs will be charged if delivered at the dealership.

View Event →
Nov
27
to Nov 30

Komatsu Tier 4 Engine Troubleshooting

This instructor-led course is designed to provide participants who have completed Komatsu Tier 4 Interim and Final engine classes, the necessary technical training to effectively troubleshoot and repair Komatsu Tier 4 Engine products (4D95, 4D107, 6D107, 6D114, 6D125, 6D140, and 6D170). This course is developed to aid the participant with the completion of Flash News 12061C. All troubleshooting procedures contained in the 12061C Flash News will be explained and performed including the use of the Insite tool, used as a diagnostic aid for the after-treatment system. Hands-on training will take place using representative Komatsu products utilizing the required tooling to complete Flash News 12061C. Hands on exercises will also include actual machine problems for the participant to troubleshoot and diagnose

View Event →
Nov
27
to Dec 1

Basic Hydraulics

AIS Basic hydraulics is a complete hydraulic system overview used on today’s heavy equipment. The technician will be taught Pascal’s Law, safety, common component function and purpose, basics of oils, oil samples and cleanliness codes, as well as schematic reading on basic hydraulic systems. They will perform disassembly and assembly of gear, vane and piston pumps, reservoirs, hoses, control valves and cylinders. The technician will gain a basic knowledge of all these components. Load sensing systems as well as fluid conditioning will be covered. The technician will perform some basic hydraulic testing and adjusting.

 

 

View Event →
Nov
13
to Nov 16

Komatsu Tier 4 Engine Troubleshooting

This instructor-led course is designed to provide participants who have completed Komatsu Tier 4 Interim and Final engine classes, the necessary technical training to effectively troubleshoot and repair Komatsu Tier 4 Engine products (4D95, 4D107, 6D107, 6D114, 6D125, 6D140, and 6D170). This course is developed to aid the participant with the completion of Flash News 12061C. All troubleshooting procedures contained in the 12061C Flash News will be explained and performed including the use of the Insite tool, used as a diagnostic aid for the after-treatment system. Hands-on training will take place using representative Komatsu products utilizing the required tooling to complete Flash News 12061C. Hands on exercises will also include actual machine problems for the participant to troubleshoot and diagnose

View Event →
Nov
7
to Nov 10

John Deere L Backhoe

The L-Series Backhoe Certification course is a 3 day instructor-led course. A combination of approximately 20% classroom and 80% hands on is used. Service procedures including special tools, adjustments, testing and diagnostics of the backhoe family will be completed during the hands-on portion of this course. The purpose of the Backhoe Loader Capstone is to verify knowledge and skills of the John Deere Dealer technician. Verification will be determined by both a hands-on and written style test and validated with an 80% or higher score. Upon successful completion of this instructor led training event, the technician will be deemed certified on the current series of Backhoe Loaders. Certification yields reimbursement for a technician’s diagnostic time spent on an in-warranty machine and also develops individuals that are the best technicians to represent John Deere, their Dealership, and support the Customer and their business needs with Backhoe Loaders. Upon completion of this course, students will be able to: 1) Efficiently and effectively diagnose and repair machine issues on John Deere Backhoe Loaders. 2) Demonstrate the knowledge and ability to perform proper diagnostics using correct diagnostic tools and equipment. 3) Properly service and "tune-up" machines to enhance customer's machine performance. The dealer technician is expected to be: Knowledgeable on all machine systems currently used on John Deere Backhoe Loaders and proficient in reading and interpreting hydraulic and electrical schematics, the use of diagnostic testing equipment, and the use of Service Advisor as a diagnostic tool and source of information. Technicians MUST have their OWN laptop, the current version of Service Advisor, and latest data disks.

View Event →
Nov
6
to Nov 10

Basic Electrical

AIS Basic Electrical Course introduces students to complete basic foundation of electrical systems used in the heavy equipment industry. Technician will be taught Ohm’s law, and how to perform calculations. The class introduces relays, fuses, batteries, diodes, capacitors, and resistors; while being taught know how to properly test them. The technician will perform basic testing on starting and charging systems, as well as schematic reading on basic electrical systems. The student will also learn how to properly use a multi-meter to perform testing.

 

View Event →
Nov
6
to Nov 9

Komatsu Tier 4 Engine Troubleshooting

This instructor-led course is designed to provide participants who have completed Komatsu Tier 4 Interim and Final engine classes, the necessary technical training to effectively troubleshoot and repair Komatsu Tier 4 Engine products (4D95, 4D107, 6D107, 6D114, 6D125, 6D140, and 6D170). This course is developed to aid the participant with the completion of Flash News 12061C. All troubleshooting procedures contained in the 12061C Flash News will be explained and performed including the use of the Insite tool, used as a diagnostic aid for the after-treatment system. Hands-on training will take place using representative Komatsu products utilizing the required tooling to complete Flash News 12061C. Hands on exercises will also include actual machine problems for the participant to troubleshoot and diagnose

View Event →
Oct
31
to Nov 3

John Deere L Backhoe

The L-Series Backhoe Certification course is a 3 day instructor-led course. A combination of approximately 20% classroom and 80% hands on is used. Service procedures including special tools, adjustments, testing and diagnostics of the backhoe family will be completed during the hands-on portion of this course. The purpose of the Backhoe Loader Capstone is to verify knowledge and skills of the John Deere Dealer technician. Verification will be determined by both a hands-on and written style test and validated with an 80% or higher score. Upon successful completion of this instructor led training event, the technician will be deemed certified on the current series of Backhoe Loaders. Certification yields reimbursement for a technician’s diagnostic time spent on an in-warranty machine and also develops individuals that are the best technicians to represent John Deere, their Dealership, and support the Customer and their business needs with Backhoe Loaders. Upon completion of this course, students will be able to: 1) Efficiently and effectively diagnose and repair machine issues on John Deere Backhoe Loaders. 2) Demonstrate the knowledge and ability to perform proper diagnostics using correct diagnostic tools and equipment. 3) Properly service and "tune-up" machines to enhance customer's machine performance. The dealer technician is expected to be: Knowledgeable on all machine systems currently used on John Deere Backhoe Loaders and proficient in reading and interpreting hydraulic and electrical schematics, the use of diagnostic testing equipment, and the use of Service Advisor as a diagnostic tool and source of information. Technicians MUST have their OWN laptop, the current version of Service Advisor, and latest data disks.

View Event →
Oct
17
to Oct 20

John Deere L Backhoe

The L-Series Backhoe Certification course is a 3 day instructor-led course. A combination of approximately 20% classroom and 80% hands on is used. Service procedures including special tools, adjustments, testing and diagnostics of the backhoe family will be completed during the hands-on portion of this course. The purpose of the Backhoe Loader Capstone is to verify knowledge and skills of the John Deere Dealer technician. Verification will be determined by both a hands-on and written style test and validated with an 80% or higher score. Upon successful completion of this instructor led training event, the technician will be deemed certified on the current series of Backhoe Loaders. Certification yields reimbursement for a technician’s diagnostic time spent on an in-warranty machine and also develops individuals that are the best technicians to represent John Deere, their Dealership, and support the Customer and their business needs with Backhoe Loaders. Upon completion of this course, students will be able to: 1) Efficiently and effectively diagnose and repair machine issues on John Deere Backhoe Loaders. 2) Demonstrate the knowledge and ability to perform proper diagnostics using correct diagnostic tools and equipment. 3) Properly service and "tune-up" machines to enhance customer's machine performance. The dealer technician is expected to be: Knowledgeable on all machine systems currently used on John Deere Backhoe Loaders and proficient in reading and interpreting hydraulic and electrical schematics, the use of diagnostic testing equipment, and the use of Service Advisor as a diagnostic tool and source of information. Technicians MUST have their OWN laptop, the current version of Service Advisor, and latest data disks.

View Event →
Sep
19
to Sep 21

John Deere Tier 4 Final Engines

This instructor-led training will focus on components, function, and flow of the Aftertreatment System which is used on many John Deere Interim Tier 4/Stage III B and Final Tier 4/Stage IV engines. Some base engine and other engine system changes will be covered primarily as they impact the Aftertreatment System. Regeneration theory, models, controls and operator interface will be covered, including observing a service regeneration. In addition, Service ADVISOR™ calibrations and interactive tests, the diagnostic test box and some diagnostics will be covered.

View Event →
Sep
11
to Sep 15

Komatsu T4 Engines (IT4 & T4F)

This instructor-led course is designed to provide participants who have Komatsu engine experience, the necessary technical training for understanding the function, maintenance, service, repair & troubleshooting of the 6D107,6D114, 6D125,& 6D140 Tier 4 final & interim engines. This course is developed to carry the participant through both Tier 4 engine systems, starting with the Tier 4 interim engines. This course will cover changes to the Base Engines, Solutions by Horsepower Rating, the Variable Geometry Turbocharger, Diesel Particulate Filter, & all the related sensors for Tier 4 interim & final engines.  The DEF System including fluid properties, tank & cooling system, tank sensor, pump & injector modules, thawing & freeze prevention logic will be covered as well. Hands-on training will take place using a Tier 4 Final & Interim Machines. On-board diagnostic testing, creation of Inducement fault codes.

View Event →
Sep
6
to Sep 8

John Deere Hydraulic Diagnostics

The Hydraulic and Hydrostatic Diagnostics course provides a technician the opportunity to reinforce knowledge and practice the skills learned in the Basic & Advanced Hydraulics courses. A short review of hydraulics and hydrostatic fundamentals is followed by hands-on practice using test equipment, Service Advisor, schematic exercises and system checkout procedures. The final day of the course is spent diagnosing hydraulic and hydrostatic problems on several different pieces of equipment.

View Event →
Aug
29
to Aug 31

John Deere Hydraulic Diagnostics

The Hydraulic and Hydrostatic Diagnostics course provides a technician the opportunity to reinforce knowledge and practice the skills learned in the Basic & Advanced Hydraulics courses. A short review of hydraulics and hydrostatic fundamentals is followed by hands-on practice using test equipment, Service Advisor, schematic exercises and system checkout procedures. The final day of the course is spent diagnosing hydraulic and hydrostatic problems on several different pieces of equipment.

View Event →
Aug
21
to Aug 25

Komatsu T4 Engines (IT4 & T4F)

This instructor-led course is designed to provide participants who have Komatsu engine experience, the necessary technical training for understanding the function, maintenance, service, repair & troubleshooting of the 6D107,6D114, 6D125,& 6D140 Tier 4 final & interim engines. This course is developed to carry the participant through both Tier 4 engine systems, starting with the Tier 4 interim engines. This course will cover changes to the Base Engines, Solutions by Horsepower Rating, the Variable Geometry Turbocharger, Diesel Particulate Filter, & all the related sensors for Tier 4 interim & final engines.  The DEF System including fluid properties, tank & cooling system, tank sensor, pump & injector modules, thawing & freeze prevention logic will be covered as well. Hands-on training will take place using a Tier 4 Final & Interim Machines. On-board diagnostic testing, creation of Inducement fault codes.

View Event →
Aug
15
to Aug 17

John Deere Electrical Diagnostics

The Electrical Diagnostics course provides a technician the opportunity to reinforce knowledge and practice the skills learned in the Level 1 and 2 Electrical courses. A short review of electrical fundamentals is followed by hands on practice using a multimeter, repairing electrical connectors, and using Service Advisor to locate electrical information. The final day of the course is spent diagnosing electrical problems on several different pieces of equipment. 

View Event →
Aug
7
to Aug 11

JCB Systems

This AIS Class focuses on JCB machine specifics including schematics online manuals and electrical systems. The course utilizes both in seat and hands on demonstrations of JCB Machines.

View Event →